30 gennaio 15, 13:00 | #151 (permalink) Top |
User Data registr.: 14-06-2010
Messaggi: 3
|
Ciao, anch'io ho la stessa macchina di savio da qualche mese, così a occhio sembra magra di filo... e forse hai qualche impostazione che ti sposta il modello in z, perché ho stampato anch'io quel case per rx e dovrebbe avere una base di appoggio Ciao Roberto |
30 gennaio 15, 13:32 | #152 (permalink) Top | |
User | Citazione:
che stampa decentemente se mi passava i suoi files di config Di repiter host e del Slicer Cosi da escludere problemi software e di errato settaggio Stasera faccio altre prove mi concentrero sopratutto sul estrtusore che mi sa che non estrude piu come all' inizio | |
30 gennaio 15, 21:31 | #154 (permalink) Top | |
Ciao Mauro. |
Qui la mia configurazione con arduino: https://www.dropbox.com/s/oitxyjrlll...arlin.rar?dl=0 Adesso provo a fare qualche foto alle impostazioni di CURA
__________________ Citazione:
| |
31 gennaio 15, 14:09 | #156 (permalink) Top |
User Data registr.: 17-06-2013 Residenza: laspezia
Messaggi: 170
|
niente problema risolto,ma ora ne sorge un altro,come si fa a stampare da sd?nel senso ho messo la prima sd che ho trovato credo da 64gb,formattata in fat32,ho messo il file .gcode ma la stampante non vede il file,mi dice sd inserita ma dopo nulla,in alternativa posso stampare da usb?
|
31 gennaio 15, 14:22 | #157 (permalink) Top | |
User Data registr.: 29-12-2012
Messaggi: 648
| Citazione:
| |
01 febbraio 15, 16:10 | #158 (permalink) Top |
User Data registr.: 29-12-2012
Messaggi: 648
|
Savio ti consiglio di leggere questa guida su slic3r almeno ti fai un idea dei vari parametri http://www.ivanbortolin.it/?p=510 |
03 febbraio 15, 00:15 | #159 (permalink) Top | |
User | Citazione:
Arduino supporta il filesistem fat16 o 32 se non erro quindi su SD troppo grandi non rischierei e non tutte le marche le digerisce io per andare tranquillo che preso la stessa che da RepRap.me nel suo kit che ho visto qui Io preferisco avere il soft di default e se è caso invertire il mosetto motore sul elettronica Attualmente ho capito che i problemi di stampa sono collegati alla parte estrusore e sto facendo delle prove per capire se è un problema legato alla velocita trascinamento filo alla vite che lo trasicna o al estrusore | |
03 febbraio 15, 17:37 | #160 (permalink) Top | ||
User | Citazione:
Citazione:
Curiosità ma che versione del FW Marlin hai mi trovo molto meno descrizione nel tuo FW e non è lo stesso che ha uppato nicola nel sito? Cmq adesso carico il tuo e vediamo come va noto da subito che tu hai impostato la stammante molto piu lenta della mia forse è quello il mio problema è settata male troppo veloce e per questo non stampa bene Questo il Mio Codice: //// MOVEMENT SETTINGS #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E #define HOMING_FEEDRATE {100*60, 100*60, 4*60, 0} // set the homing speeds (mm/min) // default settings //#define DEFAULT_AXIS_STEPS_PER_UNIT {80, 80, 3200, 620} //<-- step per unit R2 A4988 pulegge 20 denti //#define DEFAULT_AXIS_STEPS_PER_UNIT {160, 160, 6400, 1240} //<-- step per unit R2 DRV8825 pulegge 20 denti #define DEFAULT_AXIS_STEPS_PER_UNIT {100, 100, 3200, 535} //<-- step per unit R2 A4988 pulegge 16 denti //#define DEFAULT_AXIS_STEPS_PER_UNIT {200, 200, 3200, 620} //<-- step per unit R2 DRV8825 pulegge 16 denti #define DEFAULT_MAX_FEEDRATE {1000, 1000, 3, 50} // (mm/sec) #define DEFAULT_MAX_ACCELERATION {5000,5000,50,5000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. #define DEFAULT_ACCELERATION 2000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves #define DEFAULT_RETRACT_ACCELERATION 4000 // X, Y, Z and E max acceleration in mm/s^2 for retracts // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). // For the other hotends it is their distance from the extruder 0 hotend. // #define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis // #define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis // The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously) #define DEFAULT_XYJERK 15.0 // (mm/sec) #define DEFAULT_ZJERK 0.4 // (mm/sec) #define DEFAULT_EJERK 5.0 // (mm/sec) Codice: //// MOVEMENT SETTINGS #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E #define HOMING_FEEDRATE {50*60, 50*60, 4*60, 0} // set the homing speeds (mm/min) // default settings #define DEFAULT_AXIS_STEPS_PER_UNIT {100.00,100.00,3200.00,620.00} // default steps per unit for Ultimaker #define DEFAULT_MAX_FEEDRATE {500, 500, 4, 25} // (mm/sec) #define DEFAULT_MAX_ACCELERATION {1500,1500,20,2000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. #define DEFAULT_ACCELERATION 1500 // X, Y, Z and E max acceleration in mm/s^2 for printing moves #define DEFAULT_RETRACT_ACCELERATION 2000 // X, Y, Z and E max acceleration in mm/s^2 for retracts // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). // For the other hotends it is their distance from the extruder 0 hotend. // #define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis // #define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis // The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously) #define DEFAULT_XYJERK 5.0 // (mm/sec) #define DEFAULT_ZJERK 0.4 // (mm/sec) #define DEFAULT_EJERK 2.0 // (mm/sec) in caso tu hai quel estrusore Codice: // IeC HotEnd #define DEFAULT_Kp 76.42 #define DEFAULT_Ki 14.58 #define DEFAULT_Kd 100.17 | ||
Bookmarks |
| |
Discussioni simili | ||||
Discussione | Autore discussione | Forum | Commenti | Ultimo Commento |
Non ci sono parole o titoli che possano dire altro | mosppc | Elimodellismo Micromodelli | 4 | 06 settembre 13 14:02 |
ci sono cascato anche io! | LV-GDG | Batterie e Caricabatterie | 2 | 04 maggio 12 18:31 |
sono cascato anche io!! | LV-GDG | Elimodellismo Elettronica | 1 | 02 maggio 12 19:06 |
Mi sa che lo farò anche io col Baja | PhoenixXx | Automodellismo Mot. Scoppio On-Road | 13 | 01 ottobre 08 00:16 |