BaroneRosso.it - Forum Modellismo

BaroneRosso.it - Forum Modellismo (https://www.baronerosso.it/forum/)
-   Simulatori (https://www.baronerosso.it/forum/simulatori/)
-   -   Tutto su Phoenix RC (https://www.baronerosso.it/forum/simulatori/165254-tutto-su-phoenix-rc.html)

H7-25 20 aprile 15 11:09

Buongiorno ragazzi,
premetto che ho Phoenix + cavo per radio Spektrum originali ma avrei bisogno di un secondo cavo perchè mi vorrei allenare durante la pausa pranzo a lavoro. Sapete dirmi dove potrei trovare in rete solo il cavo, magari anche un clone dell'originale?
Grazie

lucioPilot 23 aprile 15 00:07

installazione phoenix
 
Ciao a tutti

Phoenix può essere installato quante volte si vuole ?

H7-25 23 aprile 15 09:45

Citazione:

Originalmente inviato da lucioPilot (Messaggio 4617713)
Ciao a tutti

Phoenix può essere installato quante volte si vuole ?

Certo

Filippo1784 23 aprile 15 19:06

raga con futaba t10j non mi va.. configurazione stand avanzata da radio niente.. l eli parta a manetta da metà stik in su


Inviato dal mio iPhone utilizzando Tapatalk

The Condor 23 aprile 15 19:56

Citazione:

Originalmente inviato da Filippo1784 (Messaggio 4618263)
raga con futaba t10j non mi va.. configurazione stand avanzata da radio niente.. l eli parta a manetta da metà stik in su


Inviato dal mio iPhone utilizzando Tapatalk



Quando calibri la radio lo stick del gas lo devi mettere in posizione centrale

Filippo1784 24 aprile 15 20:46

Citazione:

Originalmente inviato da The Condor (Messaggio 4618306)
Quando calibri la radio lo stick del gas lo devi mettere in posizione centrale


perdonami mi spieghi meglio tutto nel dettaglio gentilmente proprio da zero


Inviato dal mio iPad utilizzando Tapatalk

The Condor 24 aprile 15 21:00

Citazione:

Originalmente inviato da Filippo1784 (Messaggio 4619185)
perdonami mi spieghi meglio tutto nel dettaglio gentilmente proprio da zero


Inviato dal mio iPad utilizzando Tapatalk

dal supporto ufficiale phoenix

If your throttle control is moving from one extreme to the other with no smooth change between then you may not have calibrated your throttle channel correctly.

Open the system > your transmitter menu and look at the orange bars on the display. Find the first bar that moves when you only move the throttle stick on your radio.

Does this bar move smoothly from one extent to the other as you move the throttle stick, and is it centered when the stick is in the centre of its travel?

If not, then you should recalibrate your radio by clicking the calibrate button, making absolutely sure that:

• You have your throttle stick centered when prompted, and not at the idle position

• You do not have your IDLE-UP/STUNT mode switches active at any time before/during the calibration process



If the throttle bar appears to be reacting correctly - i.e. moving smoothly from one extent to the other as you move the stick then you may just be experiencing the rotor governor which is fitted by default to many of the helicopters in Phoenix. The governor will attempt to keep a preset RPM whenever the throttle stick is above 25%, and is the most common way of flying an R/C helicopter model. To test if this is the case, fly a model which does not have a rotor governor such as the model > change > helicopters > electric > Blade CX2 model - does this fly as you would expect?

Filippo1784 25 aprile 15 10:54

Citazione:

Originalmente inviato da The Condor (Messaggio 4619196)
dal supporto ufficiale phoenix



If your throttle control is moving from one extreme to the other with no smooth change between then you may not have calibrated your throttle channel correctly.



Open the system > your transmitter menu and look at the orange bars on the display. Find the first bar that moves when you only move the throttle stick on your radio.



Does this bar move smoothly from one extent to the other as you move the throttle stick, and is it centered when the stick is in the centre of its travel?



If not, then you should recalibrate your radio by clicking the calibrate button, making absolutely sure that:



• You have your throttle stick centered when prompted, and not at the idle position



• You do not have your IDLE-UP/STUNT mode switches active at any time before/during the calibration process







If the throttle bar appears to be reacting correctly - i.e. moving smoothly from one extent to the other as you move the stick then you may just be experiencing the rotor governor which is fitted by default to many of the helicopters in Phoenix. The governor will attempt to keep a preset RPM whenever the throttle stick is above 25%, and is the most common way of flying an R/C helicopter model. To test if this is the case, fly a model which does not have a rotor governor such as the model > change > helicopters > electric > Blade CX2 model - does this fly as you would expect?


Davvero gentilissimo risolto tutto rapidamente numero 1.


Inviato dal mio iPhone utilizzando Tapatalk

The Condor 25 aprile 15 12:45

Citazione:

Originalmente inviato da Filippo1784 (Messaggio 4619489)
Davvero gentilissimo risolto tutto rapidamente numero 1.


Inviato dal mio iPhone utilizzando Tapatalk



😉😉😉😉😉😎

Filippo1784 01 maggio 15 09:12

Citazione:

Originalmente inviato da The Condor (Messaggio 4619546)
😉😉😉😉😉😎


scusa ne ne approfitto per provare sempre con l eli a fare del volo rovesciato che curva passo e thr inseriresti sempre in phoenix? si deve usare anche l hidle?


Inviato dal mio iPhone utilizzando Tapatalk


Tutti gli orari sono GMT +2. Adesso sono le 14:24.

Basato su: vBulletin versione 3.8.11
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
E' vietata la riproduzione, anche solo in parte, di contenuti e grafica. Copyright 1998/2019 - K-Bits P.I. 09395831002