|
Citazione:
abbiate pazienza massimo |
Citazione:
- qualsiasi sia la codifica che entra nel modulo non ha importanza - il modulo 2.4Ghz ha un processore a bordo che garantisce non solo la conversione e trasmissione in 2.4Ghz di ciò che entra ma anche il protocollo su cui è basata - il fail safe è una programmazione della radio ma credo che è anche una delle poche che viene memorizzata sulla ricevente - solo la ricevente è in grado di rilevare una assenza/errore di trasmissione per cui attivare il fail safe come memorizzato - il fail safe una funzione nativa proprio del sistema digitale (PCM e 2.4GHz), in quanto è naturale che quest'ultimo riesca ad accorgersi di una condizione di disturbo e quindi di comando ricevuto corrotto Relativamente alla FF9, qui le istruzioni (in inglese) ... |
Citazione:
|
Ciao Francesco ti riferisci a questo?: http://manuals.hobbico.com/fut/tm8-manual.pdf (grazie, ho tradotto con Google, ma non ho letto nulla sulla procedura del File Safe... massimo) massimo |
Citazione:
------------------------ F/S (Fail Safe) mode setting The F/S is suggested for use as it offers a safety factor when controlling your models. It is also possible to cancel the F/S operation if you do not wish to use it. De-activating the F/S (Failsafe) As noted above, it is also possible to de-activate the failsafe setting of the receiver. Depress the F/S button on the rear of the transmitter while turning the transmitter's power on. The LEDs should begin to glow. Continue holding the button until the green LED begins to glow solidly and the red LED blinks. Re-Arming the F/S (Failsafe) To activate the failsafe once again, depress the F/S button on the rear of the transmitter while turning the transmitter's power on. The LEDs should begin to glow. Continue holding the button until the green and Red LED's begin blinking. * Please note: re-arming the F/S does not alter the pre-determined throttle servo position. To modify this setting, please follow the F/S position setting procedure. F/S position setting procedure As mentioned at "Easy Link", the R608FS starts linking process by press the Easy Link button more than two seconds. Meanwhile, when linking is done, the R608FS stores 3ch(Throttle) position as the F/S position automatically. If you need to change the F/S position but not need to re-link, set the 3ch(throttle) stick as desired position and press and hold the Easy Link button just one second. By this way, the receiver renew the F/S data for current 3ch position. Prior to doing so, ensure that the F/S is active. If not, please follow the Re- Arming of the F/S procedure as noted previously. 1 With the transmitter's throttle stick in the desired F/S position, and the receiver located within one (1) meter of the transmitter, turn on the transmitter. The green LED, located on the rear of the TM-8 transmitter module, should begin to blink. If not, power down the transmitter and turn it on once again. 2 With the transmitter on, and the green LED blinking, turn on the receiver. Press and hold the Easy Link button, located on the receiver, for approximately one second. 3 Turn off the transmitter. The throttle servo should move to the pre-determined F/S position. R608FS F/S set and Easy-link Operation 0 to 1 sec . 1 to 2 sec. More than 2 sec. 0 sec . 1 sec. 2 sec. Press and Hold time W ith TM-8 No function To set the F/S position(No re-link) Re-link(ID set) and to set the F/S position With TM-14 No function (not included in this set) Re-link(ID set) Please refer to the table below for the LED status of the receiver's condition. Green Red Status Off Solid No signal reception Solid Off Receiving signals Blink Off Receiving signals but ID is unmatched Alternate blink Unrecoverable failure (EEPROM, etc.) |
adesso la vedo anch'io !!! non so perchè, a me si era caricata solo la prima pagina ! adesso vado a tradurre. grazie e scusate massimo |
| Tutti gli orari sono GMT +2. Adesso sono le 06:35. |
Basato su: vBulletin versione 3.8.11
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
E' vietata la riproduzione, anche solo in parte, di contenuti e grafica. Copyright 1998/2019 - K-Bits P.I. 09395831002